Forums
NCKrawlers :: Forums :: NCK Tech Forums :: Pimp my 4x4
 
<< Previous thread | Next thread >>
ZR2 Truggy Build
Go to page   <<      
Moderators: Administrator, NC-Fordguy, KrawlinYJ
Author Post
gogogadgetbiker
Fri May 09 2008, 10:18PM

Registered Member #33
Joined: Fri Apr 06 2007, 11:24AM
Location: G-Vegas
Posts: 388
I hate to admit it but that's pretty much the way it happened.

2002 GMC Sonoma ZR2 SFA
HP D60 front, 5:13's,Chevy brakes, ARB, 35 spline hubs, rotated
GM 14B FF rear 5:13's, Disk, Detroit, 3/8" diff cover
Alcan Waggie 4" front springs and ZR2 4" rear springs
Highsteer/crossover steering, PSC Box
42" IROKs, Eaton 32 Bolt Beadlocks
High Angle Driveshafts
Custom T-case
Back to top
gogogadgetbiker
Sat May 17 2008, 09:23PM

Registered Member #33
Joined: Fri Apr 06 2007, 11:24AM
Location: G-Vegas
Posts: 388
Got a little more done today, don't hate on my hi-tek grill mounting system.

The hood and fenders are just sitting there, so they don't line up just yet.

I did realize today I made another big oops... The passenger side shock hoop is right in the way of the lower radiator hose "I have no idea what I am going to do about that yet", and I think I mangled one of my transmission lines trying to pull it out of the way.

Anyway, here you go.
[ image disabled ]
[ image disabled ]
[ image disabled ]
[ image disabled ]
[ image disabled ]
[ image disabled ]

2002 GMC Sonoma ZR2 SFA
HP D60 front, 5:13's,Chevy brakes, ARB, 35 spline hubs, rotated
GM 14B FF rear 5:13's, Disk, Detroit, 3/8" diff cover
Alcan Waggie 4" front springs and ZR2 4" rear springs
Highsteer/crossover steering, PSC Box
42" IROKs, Eaton 32 Bolt Beadlocks
High Angle Driveshafts
Custom T-case
Back to top
SAYWHENCJ7
Sun May 18 2008, 12:22AM
NCK Member

Registered Member #97
Joined: Sun Aug 19 2007, 04:21PM
Location: GREENVILLE
Posts: 112
nice..
Back to top
rockcity
Sun May 18 2008, 10:22PM

Registered Member #21
Joined: Tue Mar 13 2007, 05:17PM
Location: Greenville, NC
Posts: 703
is that ride height? Looks good at that height

www.ECORS.com
Back to top
gogogadgetbiker
Sun May 18 2008, 11:28PM

Registered Member #33
Joined: Fri Apr 06 2007, 11:24AM
Location: G-Vegas
Posts: 388
It will be now, after today's round of cutting stuff off.

2002 GMC Sonoma ZR2 SFA
HP D60 front, 5:13's,Chevy brakes, ARB, 35 spline hubs, rotated
GM 14B FF rear 5:13's, Disk, Detroit, 3/8" diff cover
Alcan Waggie 4" front springs and ZR2 4" rear springs
Highsteer/crossover steering, PSC Box
42" IROKs, Eaton 32 Bolt Beadlocks
High Angle Driveshafts
Custom T-case
Back to top
gogogadgetbiker
Mon Aug 04 2008, 11:53AM

Registered Member #33
Joined: Fri Apr 06 2007, 11:24AM
Location: G-Vegas
Posts: 388
Finally got back on it. Front and rear shock locations are set "after many, many agravating attempts." The 18" shocks just seem to flex forever.

[ image disabled ]
[ image disabled ]

Not thrilled about the front but due to the radiator I had few options, I just had to get something in there. No it is not removable "yet" and probably won't be unless I get a V8 in there. I don't feel that it would be that big of a deal to put in a joint after the fact if needed.

[ image disabled ]
[ image disabled ]
[ image disabled ]

The Orbital is right next to the manifold, hopefully that isn't a big problem. I guess only time will tell.

[ image disabled ]

The rear anti-rock sway bar had to be modified to clear the tires at full articulation.

[ image disabled ]
[ image disabled ]
[ image disabled ]

If anyone has some links to sites that make intake tubing "specifically the piece that bolts to the throttle body" let me know, I am going to have to hand make the intake system.

Measured for my rear driveshaft and I only have 1 3/8" of total travel in the shaft from full compression to full extension. It's amazing what a 4-link will let you do.

2002 GMC Sonoma ZR2 SFA
HP D60 front, 5:13's,Chevy brakes, ARB, 35 spline hubs, rotated
GM 14B FF rear 5:13's, Disk, Detroit, 3/8" diff cover
Alcan Waggie 4" front springs and ZR2 4" rear springs
Highsteer/crossover steering, PSC Box
42" IROKs, Eaton 32 Bolt Beadlocks
High Angle Driveshafts
Custom T-case
Back to top
SAYWHENCJ7
Mon Aug 04 2008, 12:07PM
NCK Member

Registered Member #97
Joined: Sun Aug 19 2007, 04:21PM
Location: GREENVILLE
Posts: 112
Truck looks great man let me know if you need a hand...
Back to top
gogogadgetbiker
Mon Aug 04 2008, 12:08PM

Registered Member #33
Joined: Fri Apr 06 2007, 11:24AM
Location: G-Vegas
Posts: 388
I always need a hand..

2002 GMC Sonoma ZR2 SFA
HP D60 front, 5:13's,Chevy brakes, ARB, 35 spline hubs, rotated
GM 14B FF rear 5:13's, Disk, Detroit, 3/8" diff cover
Alcan Waggie 4" front springs and ZR2 4" rear springs
Highsteer/crossover steering, PSC Box
42" IROKs, Eaton 32 Bolt Beadlocks
High Angle Driveshafts
Custom T-case
Back to top
biggy
Tue Aug 05 2008, 07:25AM

Registered Member #11
Joined: Mon Mar 12 2007, 06:55AM
Posts: 383
gogogadgetbiker wrote ...

If anyone has some links to sites that make intake tubing "specifically the piece that bolts to the throttle body" let me know, I am going to have to hand make the intake system.


www.jagsthatrun.com.. this is where I got my intake stuff, they have almost anything you need for a late model conversion.

it's a '51...it's just been modified some
Back to top
rockcity
Tue Aug 05 2008, 07:58AM

Registered Member #21
Joined: Tue Mar 13 2007, 05:17PM
Location: Greenville, NC
Posts: 703
also try Burnes Stainless. They have a lot of stuff like that as well. I got a lot of misc stuff from them for my buggy, not yet installed obviously...

looking good.

www.ECORS.com
Back to top
Hadfield4wd
Thu Aug 07 2008, 01:10PM

Registered Member #43
Joined: Sun Apr 15 2007, 02:36PM
Posts: 134
Bill,

Don't know if the orbital will be a problem or not, but either way just get a good cooler.

This is what I have.

http://store.summitracing.com/egnsearch.asp?Ntt=flx-3818&searchinresults=false&Ntk=KeywordSearch&DDS=1&N=700+4294924500+4294839040+400226+115

they have bigger as well. I haven't used it as it's not installed yet.

Matt

Back to top
gogogadgetbiker
Thu Aug 07 2008, 05:08PM

Registered Member #33
Joined: Fri Apr 06 2007, 11:24AM
Location: G-Vegas
Posts: 388
http://www.pscmotorsports.com/der13253-derale-12-heat-sink-cooler-kit-p-638.html

I have one of these just not installed

2002 GMC Sonoma ZR2 SFA
HP D60 front, 5:13's,Chevy brakes, ARB, 35 spline hubs, rotated
GM 14B FF rear 5:13's, Disk, Detroit, 3/8" diff cover
Alcan Waggie 4" front springs and ZR2 4" rear springs
Highsteer/crossover steering, PSC Box
42" IROKs, Eaton 32 Bolt Beadlocks
High Angle Driveshafts
Custom T-case
Back to top
Hadfield4wd
Fri Aug 08 2008, 12:09AM

Registered Member #43
Joined: Sun Apr 15 2007, 02:36PM
Posts: 134
very nice

Matt

Back to top
gogogadgetbiker
Sat Aug 30 2008, 08:43PM

Registered Member #33
Joined: Fri Apr 06 2007, 11:24AM
Location: G-Vegas
Posts: 388
Got the rear welded and put back in, everything is there except bump's and limit straps.
F911 Bolts throughout....
[ image disabled ]

Got a new plate a while back, I think it fits.
[ image disabled ]

[ image disabled ]

[ image disabled ]

[ image disabled ]

Welded on some D-rings for when it's on the trailer.
[ image disabled ]

2002 GMC Sonoma ZR2 SFA
HP D60 front, 5:13's,Chevy brakes, ARB, 35 spline hubs, rotated
GM 14B FF rear 5:13's, Disk, Detroit, 3/8" diff cover
Alcan Waggie 4" front springs and ZR2 4" rear springs
Highsteer/crossover steering, PSC Box
42" IROKs, Eaton 32 Bolt Beadlocks
High Angle Driveshafts
Custom T-case
Back to top
gogogadgetbiker
Sat Aug 30 2008, 08:47PM

Registered Member #33
Joined: Fri Apr 06 2007, 11:24AM
Location: G-Vegas
Posts: 388
Got a bit done on the front...

[ image disabled ]

[ image disabled ]

[ image disabled ]

[ image disabled ]

[ image disabled ]

2002 GMC Sonoma ZR2 SFA
HP D60 front, 5:13's,Chevy brakes, ARB, 35 spline hubs, rotated
GM 14B FF rear 5:13's, Disk, Detroit, 3/8" diff cover
Alcan Waggie 4" front springs and ZR2 4" rear springs
Highsteer/crossover steering, PSC Box
42" IROKs, Eaton 32 Bolt Beadlocks
High Angle Driveshafts
Custom T-case
Back to top
rockcity
Tue Sep 02 2008, 08:07AM

Registered Member #21
Joined: Tue Mar 13 2007, 05:17PM
Location: Greenville, NC
Posts: 703
looks good. those d rings are gonna be loud and I bet you cut them off after the first trip...

www.ECORS.com
Back to top
SAYWHENCJ7
Tue Sep 02 2008, 12:18PM
NCK Member

Registered Member #97
Joined: Sun Aug 19 2007, 04:21PM
Location: GREENVILLE
Posts: 112
looking good Bill sorry I couldnt make it....
Back to top
bigboyhd
Tue Sep 02 2008, 01:36PM
Registered Member #111
Joined: Mon Sep 03 2007, 10:56PM
Location: G-Vegas
Posts: 28
Yeah jaime we could have used a couple extra hands. Bill is gonna be burried in wires for the next couple of weeks, maybe you can come by and give me a hand.
Back to top
rockcity
Tue Oct 07 2008, 11:13AM

Registered Member #21
Joined: Tue Mar 13 2007, 05:17PM
Location: Greenville, NC
Posts: 703
and???

www.ECORS.com
Back to top
bigboyhd
Tue Oct 07 2008, 11:54AM
Registered Member #111
Joined: Mon Sep 03 2007, 10:56PM
Location: G-Vegas
Posts: 28
Bill Is in Harlan, he should be back tonight.
Back to top
Go to page   <<       

Jump:     Back to top

Syndicate this thread: rss 0.92 Syndicate this thread: rss 2.0 Syndicate this thread: RDF
Powered by e107 Forum System